visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model b d 0826j50200ahf rev a ultra low profile 0805 balun 50 to 200 balanced description the BD0826J50200AHF is a low profile sub miniature balanced to unbalanced transformer designed for differential in puts and output locations on next generation wireless chipsets in an easy to use surf ace mount package covering the gsm, dcs, pcs, umts, cdma and 802.11 b+g+n frequenc ies. the BD0826J50200AHF is ideal for high volume manufactur ing and is higher performance than traditional ceramic, and lumped el ement baluns. the BD0826J50200AHF has an unbalanced port impedance of 50 and a 200 balanced port impedance. this transformation enable s single ended signals to be applied to differential ports on modern integrated chipsets. the output ports have equal amplitude (3db) with 180 degree phase differ ential. the BD0826J50200AHF is available on tape and reel for pick and place hi gh volume manufacturing. detailed electrical specifications: specifications subject to change without notice. room (25 c) parameter min. typ. max unit frequency 800 2600 mhz unbalanced port impedance 50 balanced port impedance 200 return loss 8.5 13 db insertion loss* 1.2 1.5 db amplitude balance 0.4 1.3 db phase balance 3 7 degrees cmrr 30 db power handling 2 watts features: ? 800 C 2600 mhz ? 0.7mm height profile ? 50 ohm to 2 x 100 ohm ? gsm/dcs/pcs/umts/cdma ? low insertion loss ? input to output dc isolation ? surface mountable ? tape & reel ? nonconductive surface ? rohs compliant ? halogen free operating temperature 55 +85 oc * insertion loss stated at room temperature (insert ion loss is approximately 0.1 db higher at +85 oc) outline drawing mechanical outline dimensions are in millimeters 2.040.10 1.290.10 0.680.07 1 2 3 6 5 6x 0.30 6x 0.22 4x 0.65 6x 0.98 orientation marker denotes pin location 4 orientation marker denotes pin location top view (near side) side view bottom view (far side) 5 4 2 16 3 pin balanced port gnd nc balanced port gnd/dc feed unbalanced port designation 2x 0.15 4x 0.37 +rf gnd
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model b d 0826j50200ahf rev a typical broadband performance: 500 mhz. to 8.0 ghz. return loss input 36 33 30 27 24 21 18 15 12 9 6 3 0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 frequency [mhz] [db] insertion loss 3.6 3.3 3 2.7 2.4 2.1 1.8 1.5 1.2 0.9 0.6 0.3 0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 frequency [mhz] [db] amplitude balance 2 1.5 1 0.5 0 0.5 1 1.5 2 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 frequency [mhz] [db] phase balance 20 15 10 5 0 5 10 15 20 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 frequency [mhz] deg cmrr 36 33 30 27 24 21 18 15 12 9 6 3 0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 frequency [mhz] [db]
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model b d 0826j50200ahf rev a typical performance: 700 mhz. to 2700 mhz. return loss input 36 33 30 27 24 21 18 15 12 9 6 3 0 700 950 1200 1450 1700 1950 2200 2450 2700 frequency [mhz] [db] insertion loss 3.6 3.3 3 2.7 2.4 2.1 1.8 1.5 1.2 0.9 0.6 0.3 0 700 950 1200 1450 1700 1950 2200 2450 2700 frequency [mhz] [db] amplitude balance 2 1.5 1 0.5 0 0.5 1 1.5 2 700 950 1200 1450 1700 1950 2200 2450 2700 frequency [mhz] [db] phase balance 20 15 10 5 0 5 10 15 20 700 950 1200 1450 1700 1950 2200 2450 2700 frequency [mhz] deg cmrr 36 33 30 27 24 21 18 15 12 9 6 3 0 700 950 1200 1450 1700 1950 2200 2450 2700 frequency [mhz] [db]
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model b d 0826j50200ahf rev a mounting configuration: in order for xinger surface mount components to wor k optimally, the proper impedance transmission line s must be used to connect to the rf ports. if this condition is not satisfied, insertion loss, isolation and vsw r may not meet published specifications. all of the xinger components are constructed from o rganic ptfe based composites which possess excellen t electrical and mechanical stability. xinger compone nts are compliant to a variety of rohs and green st andards and ready for pbfree soldering processes. pads are gol d plated with a nickel barrier. an example of the pcb footprint used in the testing of these parts is shown below. an example of a dc biased footprint is also shown below. in specific designs , the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. no bias footprint 6x .41 6x .33 .04 4x .25 .66 3x transmission lines plated thru holes to ground plated thru holes to ground circuit pattern footprint pad (s) solder resist mounting footprint dimensions are in millimeters dc bias footprint 6x .41 6x .33 .04 4x .25 .66 3x transmission lines plated thru holes to ground circuit pattern footprint pad (s) solder resist mounting footprint dimensions are in millimeters capacitor plated thru holes to ground dc bias
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model b d 0826j50200ahf rev a packaging and ordering information parts are available in reel and are packaged per ei a 4812. parts are oriented in tape and reel as sh own below. minimum order quantities are 4000 per reel. see model numbers be low for further ordering information . .25 2.41 8.00 4.00 2.00 .81 1.75 3.50 4.00 1.60
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: anaren: ? BD0826J50200AHF
|
